Produccion textil

World Cheapest FFP3 Valveless Respirator Face Mask

World Cheapest FFP3 Valveless Respirator Face Mask
Vertical fold-flat FFP3 respirator face mask, without exhalation valve
Welded elastic earloops
Imbedded nose clip, sponge nose lining
CE approved by UNIVERSAL (NB no. 2163)
Tested and certified according to EN 149:2001+A1:2009
Class: FFP3 NR

This respirator mask is certified and classified as FFP3 under EU standard EN 149:2001+A1:2009.

EN 149:2001+A1:2009 - Respiratory protective devices - Filtering half masks to protect against particles.

This European Standard specifies the minimum requirements for filtering half masks used as respiratory protective devices, specifically against particles, and the required laboratory and practical performance tests to assess masks' compliance.

EN 149:2001+A1:2009 classified half masks into three types according to their filtering capacities: FFP1, FFP2 and FFP3. Respirators that meet the requirements of EN 149:2001+A1:2009 are designed to protect against solids, water-based aerosols, and oil-based aerosols.

FFP3 masks have a minimum of 99% filtration percentage and maximum 2% leakage to the inside. They are mainly used in construction, agriculture, and by healthcare professionals against influenza viruses.

BSI COVID-19 Filtering Face Mask FFP2 Respirator

BSI COVID-19 Filtering Face Mask FFP2 Respirator
Disposable FFP2 Particulate Respirator | BSI COVID-19 Filtering Half Face Mask

This respirator mask is certified and classified in accordance with BSI's PPE for Healthcare Professionals 2020/403 - Respiratory Protective Equipment Technical Specification and therefore carries the CE mark. Certification under Module B, EU Type-Examination and Module C2, EC Quality Control, will be issued by BSI Group The Netherlands B.V., Say Building, John M. Keynesplein 9, 1066 EP, Amsterdam, Netherlands (Notified Body Number 2797).

Module B Certificate No. CE 728354
Module C2 Certificate No. CE 728374

To technical specifiction Annex II (EHSR) of the PPE Regulation (EU) 2016/425. PPE for use by health care professionals as per Commission Recommendation 2020/403.

This filtering half mask is manufactured for COVID-protection only. This filtering half mask is not a PPE device for general useand shall not be used for purposes other than protection against COVID-19.

EN 149:2001+A1:2009 classified half masks into three types according to their filtering capacities: FFP1, FFP2 and FFP3. Respirators that meet the requirements of EN 149:2001+A1:2009 are designed to protect against solids, water-based aerosols, and oil-based aerosols.

FFP2 masks have a minimum of 94% filtration percentage and maximum 8% leakage to the inside. They are mainly used in construction, agriculture, and by healthcare professionals against influenza viruses.

Features:
VIRGIN plastic materials made and odorless.
This respirator face mask offers a flexible nose piece that helps form a closure for better protection against exposure.
CE approved and FFP2 class, not reusable.
This respirator half face mask is for use by healthcare workers, first responders and other personnel involved in the efforts to contain the COVID-19 virus and avoid its further spread.
Vertical-fold flat, easy storage and transportation in a pocket.

Specifcations:
5 layers, Hydrophobic non-woven fabric (outer) + Coarse filter + Meltblown filter + Meltblown filter + Soft absorbent non-woven fabric

High-Density Knit Microfiber Blend Cleanroom Wipes

High-Density Knit Microfiber Blend Cleanroom Wipes
High-Density Knit Polyester-Nylon Microfiber Blend Cleanroom Wipes

Features:
High-Density knit continuous filament polyester-nylon microfibers (70% polyester + 30% nylon).
Soft-texture microfiber cleanroom wipes have tiny microfibers that cling to even the smallest contaminant particles without scratching the surface.
The soft, durable wipes are optimally suited for scratch-sensitive surfaces as well as for fine cleaning of small components. Laser-cut sealed edges ensure no lint is left behind
High absorptive capacity and rapid absorption rate

Production process:
Laser/ultrasonic sealed edges ensure lint-free.
Laundered with 18 MΩ pure.
Packaged in class 100/1000 (ISO5/6) cleanrooms.
Professional static clean technology ensures the lowest containing of particles.

Pre-cautions:
Double chamber vacuum packaging. The outer chamber should be taken away before a pack of cleanroom wipers is brought in workshops.
Wrap the edges to the upper middle of wipers before wiping because the edges may damage the product surface to be wiped.
Do not cut any wipe by yourself because it will cause lints from the cut edge
Keep away from fire, and do not wipe high-temperature surfaces.

Packing details:
Size Inner pack Outer pack
4"*4" 400 (±1%) 20
6"*6" 100 (±1%) 40
9"*9" 100 (±1%) 20

Woven Polyester-Nylon Microfiber Cleanroom Wipes

Woven Polyester-Nylon Microfiber Cleanroom Wipes
Woven Polyester-Nylon Microfiber Blend Cleanroom Wipes

Features:
Woven short filament polyester-nylon microfibers (70% polyester + 30% nylon).
Low elasticity.
Wear-resistant, strong polishing capacity.
Extra-low lint.
High absorptive capacity and strong chemical resistance

Production process:
Laser/ultrasonic sealed edges ensure lint-free.
Laundered with 18 MΩ pure.
Packaged in class 100/1000 (ISO5/6) cleanrooms.
Professional static clean technology ensures the lowest containing of particles.

Pre-cautions:
Double chamber vacuum packaging. The outer chamber should be taken away before a pack of cleanroom wipers is brought in workshops.
Wrap the edges to the upper middle of wipers before wiping because the edges may damage the product surface to be wiped.
Do not cut any wipe by yourself because it will cause lints from the cut edge
Keep away from fire, and do not wipe high-temperature surfaces.

Packing details:
Size Inner pack Outer pack
4"*4" 400 (±1%) 20
6"*6" 100 (±1%) 40
9"*9" 100 (±1%) 20

100% Polyester Lint-free Wipers Cleanroom Wipes CN

100% Polyester Lint-free Wipers Cleanroom Wipes CN
100% Polyester Lint-free Wipers | Cleanroom Wipes

Features:
Knitted low-elasticity continuous filaments of 100% polyester (stripe grain or grid grain).
Stripe grain wipes are suitable for sensitive surface production.
Grid grain wipes are suitable for wiping stubborn stains
Good absorbency and high efficiency
Work well with IPA, acetone and other solvents
Laser sealed edges ensure an ultra-low level of lint.
High absorptive capacity and rapid absorption rate

Production process:
Laser/ultrasonic sealed edges ensure lint-free.
Laundered with 18 MΩ pure.
Packaged in class 100/1000 (ISO5/6) cleanrooms.
Professional static clean technology ensures the lowest containing of particles.

Pre-cautions:
Double chamber vacuum packaging. The outer chamber should be taken away before a pack of cleanroom wipes is brought in workshops.
Wrap the edges to the upper middle of wipes before wiping because the edges may damage the product surface to be wiped.
Do not cut any wipe by yourself because it will cause lints from the cut edge
Keep away from fire, and do not wipe high-temperature surfaces.

Packing details:
Size Inner pack Outer pack
4"*4" 400 (±1%) 20
6"*6" 100 (±1%) 40
9"*9" 100 (±1%) 20

Low-Cost Soft Polyester Microfiber Cleanroom Wipes

Low-Cost Soft Polyester Microfiber Cleanroom Wipes
Soft-Texture Polyester Microfiber Cleanroom Wipes

Features:
Interlock knit 100% continuous filament polyester microfibers.
Soft-texture polyester microfiber cleanroom wipes have tiny microfibers that cling to even the smallest contaminant particles without scratching the surface.
The soft, durable wipes are optimally suited for scratch-sensitive surfaces as well as for fine cleaning of small components. Laser-cut sealed edges ensure no lint is left behind
High absorptive capacity and rapid absorption rate

Production process:
Laser/ultrasonic sealed edges ensure lint-free.
Laundered with 18 MΩ pure.
Packaged in class 100/1000 (ISO5/6) cleanrooms.
Professional static clean technology ensures the lowest containing of particles.

Pre-cautions:
Double chamber vacuum packaging. The outer chamber should be taken away before a pack of cleanroom wipers is brought in workshops.
Wrap the edges to the upper middle of wipers before wiping because the edges may damage the product surface to be wiped.
Do not cut any wipe by yourself because it will cause lints from the cut edge
Keep away from fire, and do not wipe high-temperature surfaces.

Packing details:
Size Inner pack Outer pack
4"*4" 400 (±1%) 20
6"*6" 100 (±1%) 40
9"*9" 100 (±1%) 20

Polyester-Nylon Microfiber Blend Cleanroom Wipes

Polyester-Nylon Microfiber Blend Cleanroom Wipes
Soft-Texture Polyester-Nylon Microfiber Blend Cleanroom Wipes

Features:
Interlock knit continuous filament polyester-nylon microfibers (70% polyester + 30% nylon).
Soft-texture microfiber cleanroom wipes have tiny microfibers that cling to even the smallest contaminant particles without scratching the surface.
The soft, durable wipes are optimally suited for scratch-sensitive surfaces as well as for fine cleaning of small components. Laser-cut sealed edges ensure no lint is left behind
High absorptive capacity and rapid absorption rate

Production process:
Laser/ultrasonic sealed edges ensure lint-free.
Laundered with 18 MΩ pure.
Packaged in class 100/1000 (ISO5/6) cleanrooms.
Professional static clean technology ensures the lowest containing of particles.

Pre-cautions:
Double chamber vacuum packaging. The outer chamber should be taken away before a pack of cleanroom wipers is brought in workshops.
Wrap the edges to the upper middle of wipers before wiping because the edges may damage the product surface to be wiped.
Do not cut any wipe by yourself because it will cause lints from the cut edge
Keep away from fire, and do not wipe high-temperature surfaces.

Packing details:
Size Inner pack Outer pack
4"*4" 400 (±1%) 20
6"*6" 100 (±1%) 40
9"*9" 100 (±1%) 20

Factory-D Polyester Wiping Cloths Cleanroom Wipers

Factory-D Polyester Wiping Cloths Cleanroom Wipers
Factory-Direct Polyester Wiping Cloths | Cleanroom Wipers

Features:
Knitted low-elasticity continuous filaments of 100% polyester (stripe grain or grid grain).
Stripe grain wipers are suitable for sensitive surface production.
Grid grain wipers are suitable for wiping stubborn stains
Good absorbency and high efficiency
Work well with IPA, acetone and other solvents
Laser sealed edges ensure an ultra-low level of lint.
High absorptive capacity and rapid absorption rate

Production process:
Laser/ultrasonic sealed edges ensure lint-free.
Laundered with 18 MΩ pure.
Packaged in class 100/1000 (ISO5/6) cleanrooms.
Professional static clean technology ensures the lowest containing of particles.

Pre-cautions:
Double chamber vacuum packaging. The outer chamber should be taken away before a pack of cleanroom wipers is brought in workshops.
Wrap the edges to the upper middle of wipers before wiping because the edges may damage the product surface to be wiped.
Do not cut any wipe by yourself because it will cause lints from the cut edge
Keep away from fire, and do not wipe high-temperature surfaces.

Packing details:
Size Inner pack Outer pack
4"*4" 400 (±1%) 20
6"*6" 100 (±1%) 40
9"*9" 100 (±1%) 20

Fully-auto Valved Cup Mask Machine Production Line

Fully-auto Valved Cup Mask Machine Production Line
Fully-automatic FFP2/N95 Cup-Shaped Mask Making Machine | Valved Respirtor Production Line

This production line for producing FFP2/FFP3 cup-shaped face masks with valves and it makes 3-to-6-ply valved respirators/masks automatically by the following procedures.
1) Unwinding and feeding non-woven fabrics;
2) Forming and cutting cups;
3) Feeding and mounting nose clips;
4) Feeding and stapling headloops.
5) Cutting holes for exhalation valves;
6) Fitting and welding exhalation valves.

The above process is done automatically and continuously by PLC.

Features:
1) Fully-automatic.
2) Stick nose clips externally at a constant temperature. No damage and strong fitting.
3) Earloops are installed by stapling automatically. Adjustable on length, reliable and
strong-tension.
4) Easy to use. The touch-screen control system makes operation easy.
5) Alarm when the fed material breaks or is in short.
6) The valve system is possible to be turned off by setting on touch screen to produce valveless cup masks.

Specifications:
Power supply: 14.5kW
Capacity: 15-25 pcs/min
Weight: 4,650 kg
Dimensions: 12,000(L)*2,200(W)* 1,500 (H)mm
Site level: class 100,000 cleanroom
Compressed air: 6 bar, pre-filtered, 23L/min

0.075€, 3-ply Disposable Face Masks
We are a Bulgarian company producing 3-ply Disposable Face Masks (Type IIR).
CE certified in compliance with EN 14683 + AC:2019 standard
Bacterial filtration efficiency (BFE) (%) 99,10.
Colors: white, blue, pink, black.
Standard Packaging: 50 pieces per box.

We could offer you 0.075 EUR per piece, EXW our Factory in Plovdiv, Bulgaria, (of course there are discounts for a large quantity).

Extra printing of customized box with your brand is also possible.

For more details e-mail: m.vasilev@tafprint.bg
€ 0.0

True-CE Certified FFP3 Valved Cup Respirator Mask

True-CE Certified FFP3 Valved Cup Respirator Mask
FFP3 Cup-Shaped Valved Respirator Face Mask
Easy to breathe with an exhalation valve
CE approved by UNIVERSAL (NB no. 2163)
Tested and certified according to EN 149:2001+A1:2009
Class: FFP3 NR

This valved respirator mask is certified and classified as FFP3 under EU standard EN 149:2001+A1:2009.

EN 149:2001+A1:2009 - Respiratory protective devices - Filtering half masks to protect against particles.

This European Standard specifies the minimum requirements for filtering half masks used as respiratory protective devices, specifically against particles, and the required laboratory and practical performance tests to assess masks' compliance.

EN 149:2001+A1:2009 classified half masks into three types according to their filtering capacities: FFP1, FFP2 and FFP3. Respirators that meet the requirements of EN 149:2001+A1:2009 are designed to protect against solids, water-based aerosols, and oil-based aerosols.

FFP3 masks have a minimum of 99% filtration percentage and maximum 2% leakage to the inside. They are mainly used in construction, agriculture, and by healthcare professionals against influenza viruses.

CE Certified FFP2 Cup Valved Respirator Face Mask

CE Certified FFP2 Cup Valved Respirator Face Mask
FFP2 Cup-Shaped Valved Respirator Face Mask
Easy to breathe with an exhalation valve
CE Certified by APAVE Sudeurope (NB no. 0082)
Tested and certified according to EN 149:2001+A1:2009
Class: FFP2 NR

This valved respirator mask is certified and classified as FFP2 under EU standard EN 149:2001+A1:2009.

EN 149:2001+A1:2009 - Respiratory protective devices - Filtering half masks to protect against particles.
This European Standard specifies the minimum requirements for filtering half masks used as respiratory protective devices, specifically against particles, and the required laboratory and practical performance tests to assess masks' compliance.

EN 149:2001+A1:2009 classified half masks into three types according to their filtering capacities: FFP1, FFP2 and FFP3. Respirators that meet the requirements of EN 149:2001+A1:2009 are designed to protect against solids, water-based aerosols, and oil-based aerosols.

FFP2 masks have a minimum of 94% filtration percentage and maximum 8% leakage to the inside. They are mainly used in construction, agriculture, and by healthcare professionals against influenza viruses.

APAVE CE Approved Cup FFP2 Respirator Face Mask CN

APAVE CE Approved Cup FFP2 Respirator Face Mask CN
FFP2 Cup-Shaped Respirator Face Mask (without valve)
CE Approved by APAVE Sudeurope (NB no. 0082)
Tested and certified according to EN 149:2001+A1:2009
Class: FFP2 NR

This respirator mask is certified and classified as FFP2 under EU standard EN 149:2001+A1:2009.

EN 149:2001+A1:2009 - Respiratory protective devices - Filtering half masks to protect against particles.
This European Standard specifies the minimum requirements for filtering half masks used as respiratory protective devices, specifically against particles, and the required laboratory and practical performance tests to assess masks' compliance.

EN 149:2001+A1:2009 classified half masks into three types according to their filtering capacities: FFP1, FFP2 and FFP3. Respirators that meet the requirements of EN 149:2001+A1:2009 are designed to protect against solids, water-based aerosols, and oil-based aerosols.

FFP2 masks have a minimum of 94% filtration percentage and maximum 8% leakage to the inside. They are mainly used in construction, agriculture, and by healthcare professionals against influenza viruses.

CE Approved FFP2 Particulate Respirator Face Mask

CE Approved FFP2 Particulate Respirator Face Mask
Disposable Particulate Respirator | FFP2 Filtering Half Face Mask

This respirator mask is approved and classified as FFP2 under EU standard EN 149:2001+A1:2009.

EN 149:2001+A1:2009 - Respiratory protective devices - Filtering half masks to protect against particles.
This European Standard specifies the minimum requirements for filtering half masks used as respiratory protective devices, specifically against particles, and the required laboratory and practical performance tests to assess masks' compliance.
EN 149:2001+A1:2009 classified half masks into three types according to their filtering capacities: FFP1, FFP2 and FFP3. Respirators that meet the requirements of EN 149:2001+A1:2009 are designed to protect against solids, water-based aerosols, and oil-based aerosols.

FFP2 masks have a minimum of 94% filtration percentage and maximum 8% leakage to the inside. They are mainly used in construction, agriculture, and by healthcare professionals against influenza viruses.

Features:
VIRGIN plastic materials made and odorless.
This respirator face mask offers a flexible nose piece that helps form a closure for better protection against exposure.
CE approved and FFP2 class, not reusable.
This respirator half face mask protects against airborne pathogens and reduces the risk of infection.
Fold flat, easy storage and transportation in a pocket.

Specifcations:
5 layers, Hydrophobic non-woven fabric (outer) + Coarse filter + Meltblown filter + Meltblown filter + Soft absorbent non-woven fabric

On Stock - 3Ply Surgical Mask 0.32eur/pcs EN14683

On Stock - 3Ply Surgical Mask 0.32eur/pcs EN14683
Masks are in stock in Poland and ready for shipment within 24 hours.
Currently available 113000pcs.

One mask - 0.32euro

3 Ply non woven Surgical masks heat pressed and certified.

Masks are made of three spheres: 1 ball - non-woven material, 2 ball - filter paper (protection against viruses and bacteria by 98%), 3 ball - non-woven material;
Aluminum retainer, nose clip;
With rubber loops;
Non-sterile;
For single use;
● 1 Box contain 50 pieces
● 1 Carton contain 40 boxes
Product Type: Disposable Medical Face Mask
BFE: ≥98%
CE certified in compliance with EN 14683:2019 standard.

We offer shipping within 48 hours from our warehouse from Poland to every European Union country.

A serious buyer welcome
€ 0.32

Industrial B2B Marketplace - Ofertas de Negocios